Generation Ii Expander Dies Sinclair International
"Today, if you do not want to disappoint, Check price before the Price Up.Generation Ii Expander Dies Sinclair International You will not regret if check price." price comparisons of Generation Ii Expander Dies Sinclair International
Generation Ii Expander Dies Sinclair International.
Our Generation II Expander Dies completely capture the mandrel within the die so the mandrel cannot pull out. An O-ring in the die cap allows the mandrel to float a bit and find its own center within the case neck. All three Generation II dies are precision machined from stainless steel and the 7/8 inch - 14 dies include the Sinclair Stainless Steel Split Lock Ring. Large caliber expander dies accept only 35 to 50 caliber mandrels. All expander mandrels for Sinclair Expander Bodies are sold separately: Find Mandrels here.
Sinclair, Issue:5B, Page:017
Mark Ii Induction Annealing Machine Amp Annealing.
The Mark II AMP Induction annealing machine adds some advances over the original Mark I. First off, the Mark II annealer now works with cartridges from 17 Hornet to 50 BMG. Additional air intakes and upgraded cooling fans provide improved airflow and better cooling for extended annealing sessions. Possibly the most exciting feature of the Mark II annealer is the additiona of pre-loaded AZTEC mode allowing users complete independence in determining the exact, correct annealing setting, regardless of cartridge, brand neck wall thickness or lot.
- Larger inductor to suit 50 BMG.
- Capable of annealing everything from .17 Hornet to 50 BMG.
- Significantly more output power.
- Ceramic heat shield in the inductor to aid in heat management.
- Superior cooling allowing near indefinite run time on smaller cases such as 223.
- User replaceable pilot boss should the existing one get cross threaded or damaged.
- AZTEC MODE included and ready to use.
Ultimate Trimmer & Platform Kit Sinclair/l.e. Wilson.
SINCLAIR STAINLESS ULTIMATE TRIMMER - The legendary L.E. Wilson Case Trimmer has just gotten better. Exclusive to Sinclair International, the L.E. Wilson Case Trimmer is now offered in a Stainless Steel model. We’ve paired the most accurate trimmer in the world with our Sinclair Micrometer head to create the Sinclair Stainless Ultimate Trimmer.
The L.E. Wilson Case Trimmer aligns and holds your cases square to the cutter during the trim process. This results in a virtually identical trim length for each case. It is accomplished with L.E. Wilson’s unique case holder system which holds the case by the body taper. The trimmer case holder, cutter housing, and micrometer adjustment unit sit in perfect alignment. No pilots or collets are utilized which could influence the trim results negatively. Now in stainless steel, the L.E. Wilson Trimmer is built to last for a lifetime of use.
Our Sinclair Micrometer head allows the reloader to easily adjust trim length in increments of .001" with an adjustment length of over 2". Our micrometer reads in “actual” case length, making it the most pleasurable micro trimmer to work with. Determine your trim length, dial to the exact length on the micrometer, and you’re ready – it’s that simple. The micrometer features crisp, easy-to-read engravings and may be locked in place when set. Easily accommodates cases from 22 Hornet to 416 Rigby. When trimming cases shorter than 1.3” such as pistol cases, the use of a spacer (part number WX11) is necessary.
Completing the Sinclair Stainless Ultimate Trimmer is our Sinclair Mounting Stand with Shark Fin Clamp. This system makes easy work of installing and removing your trimmer case holder in a smooth “swing-arm” motion. The Shark Fin trimmer clamp secures the case head firmly against the micrometer adjustment head for a quick and accurate, chatter-free trim. * Trimmer Case Holders and accessories sold separately.
PLATFORM - The idea for this platform originated from a writer/customer of ours. The platform is a mounting board for the L.E. Wilson trimmer series that provides storage space for nine (9) case holders and a tapping block for knocking the cases out of the holder. The polyethylene platform has rubber feet, but most of us prefer it c-clamped to the bench.
Big Book Catalog, Issue:68, Page:529
Sinclair, Issue:5B, Page:010
Case Neck Annealing Machine Bench-Source.
The BENCH-SOURCE case neck annealing machine is used exclusively to anneal and refurbish your Bottle Neck and Long Straight Wall cartridge cases for reloading. It will restore your case necks to ‘like new’ condition and extend the life of your cartridge cases. The net result is reduced reloading cost and improved accuracy. The uniformity of case neck tension will allow you to seat your bullets with less run out and more consistency in your reloads. Can be used with one or two heat sources since the cartridge case spins on a stationary spindle while heating. Heating times can be adjusted from 1.5 to 10 seconds. Manufactured out of aluminum and fan cooled; no plastic to bow or warp and the table acts as a heat sink to ensure cartridge case head integrity. This unit will process about 500-600 cartridges per hour, expect an average time of 4-5 seconds for heating and 2 seconds for indexing for a standard 308 case.
Case Prep Xpress Lyman.
One-Stop Machine Helps You Quickly Perform Brass Prep
All-in-one power tool includes the most popular case preparation accessories in one unit driven by a single high-torque, low-RPM motor ideally suited to case prep work. Nothing else to buy to get started! Quick, easy cleanup, too - just brush all the brass chips into the removable collection pan. Includes attachments to perform these case prep operations: deburr case neck inside (VLD) and outside; clean/lubricate case neck; clean/uniform primer pocket and ream out primer crimp on military brass (includes attachments for both large and small pockets). Comes with case neck brushes in .25, .30, .38 and .45 calibers, plus Mica case neck lube and a handy clean-up brush.
1911, Issue:11, Page:065
Big Book Catalog, Issue:68, Page:529
Sinclair, Issue:5B, Page:008
SPECS: 125 rpm tool speed. Available in 110 or 230 volt model. 230V comes with a proprietary plug for international.
Carbide Expander Mandrels Sinclair International.
Yields Closer Tolerances and More Lubricity
Sinclair Carbide Neck Expander Mandrels are ground from solid carbide stock, which yields closer tolerances and more lubricity. Carbide is also better at resisting galling which can leave behind material and scratch the inside of your necks.
The shape, finish, and size are the result of years of use and experimentation by many hand loaders. Sinclair expander mandrels are made .001" smaller than bullet diameter. Using an expander mandrel prior to neck turning sizes the case to fit the neck turning mandrels perfectly, or use prior to bullet seating to get more concentric necks and perfect neck tension.
All Sinclair Mandrels are designed for use with the Sinclair Expander Die and all Sinclair Neck Turning Tools.